Unknown Netbook fake Vaio N450 Jmicron Lan Slic none

[1234s282]

under the circumstances that this laptop was bought you may have got a proper fake :S http://www.techpinas.com/2009/07/fake-so...china.html

Admin

[LatinMcG75]

haha good stuff. yeah i had a feeling it looked similar to a samsung.
ill run cpu-z. and the wbflash.

the wbflash shows ModelName: Pine Trail - NP11 current version: 6.00 new ver R0120Z4 and says its not supported in this model on a popup.
was looking into the epson. seems its a nettop not a netbook . so samsung or sager or clevo it might be
edit.. seems like OLIVETTI M1025 or averatec n1200 but different location of ports.

BINGO Soltech PT21 and i need PT21 flash tool.zip
http://lzerp.com/bbs/attachment.php?aid=8825&k=57e45bd8c7223818ccedc4ed70393e5c&t=1298745228&sid=Ook6t0

how i found it : in SIW.exe the bios startign segment is E803h so i searched for n450 E803h and found soem chineese site.. translate and there it was.
original bios http://www.soltech.com.cn/uploads/PT21_B1.0_E1.0.zip

[LatinMcG75]

heres the readme translated. .seems im missing WPC.ROM for EC flashing

Chinese to English translation
Flash the BIOS method:

Method 1. With burner burner

1. The Flash ROM into the burner outlet;

2. Open the burner power, run the burning software, select the correct device type;

3. In the burning software, open devel35p.rom;

4. The implementation of programming and verification.


Method 2. Burning with burning software

1. For MS-DOS startup disk (U disk or hard drive);

2. Copy of the Flash tool package to the startup disk;

3. Copy flashabl.rom to Flash tool package directory. If the BIOS file is not flashabl.rom, need to first rename it into flashabl.rom;

4. From MS-DOS boot disk, switch paths to Flash tool package and flashabl.rom directory, run PTFB1.bat.



Flashed EC methods:

Method 1. With burner burner

1. The Flash ROM into the burner outlet;

2. Open the burner power, run the burning software, select the correct device type;

3. In the burning software, open wpc.rom;

4. The implementation of programming and verification.


Method 2. Burning with burning software

1. For MS-DOS startup disk (U disk or hard drive);

2. Copy of the Flash tool package to the startup disk;

3. Copy WPC.rom to Flash tool package directory. If the EC document is not WPC.rom, need to first rename it into WPC.rom;

4. From MS-DOS boot disk, switch paths to Flash tool package and flashabl.rom directory, run PTFE1.bat.


Note:
1. Please do not modify the PTFB1.bat, PTFE1.bat content. If you need to modify phlash16.exe or flupdate.exe parameters, please consult a technician.
2. Flashabl.rom burning can only be used with programming software BIOS, and devel35p.rom burn burner can only be used with the BIOS, not to be confused, or BIOS does not work.

[LatinMcG75]

i cant flash it i get:
part id not found in table of supported parts
i think i have to do something before flashing slic.
i found the WPC.ROM in original bios

[LatinMcG75]

sems i have W25x80 (001300EF) and the flupdate.cfg is not working
[START CONFIG]
# Winbond W25x80
# ---------------
FLASH_ID = 0x13EF # Device ID & Manufacture
FLASH_SIZE = 1024 # (1M) Flash size in KBytes
SECTOR_DEF = 256:4K # 256 sectors of 4K
# The format is: nK,nK,....,nK
# n - number of sectors
# s - size of sectors
BLOCK_SIZE = 64 # (64K) block size in Kbytes. If block erase is not supported then
# block size should be equal to FLASH_SIZE
PAGE_SIZE = 256 # Page size in bytes
PROG_SIZE = 0xFF # Max number of bytes that can be program at on time. FF --> means page size
READ_DEV_ID_TYPE = 0 # Read Device ID type.
# There are two ways to read the flash ID (depending on the flash type).
# A. Send the "Read ID" op-code, send 3 dummy address bytes and then read the ID bytes
# B. Send the "Read ID" op-code and immediately read the ID bytes.
# When the value in this field is 0x47, method B is used. Otherwise
# (any other value) method A is used.

# Define spi Flash commands
# --------------------------
CMD_READ_DEV_ID = 0x90 # Read device ID command.
CMD_WRITE_STAT_EN = 0x06 # Enable write to status register
CMD_WRITE_EN = 0x06 # Write enable
CMD_READ_STAT = 0x05 # Read status register
CMD_WRITE_STAT = 0x01 # Write status register
CMD_PROG = 0x02 # Page program, or byte program.
CMD_SECTOR_ERASE = 0x20 # Sector erase
CMD_BLOCK_ERASE = 0xD8 # Block erase

# Define device busy bits in status register
# -------------------------------------------
STATUS_BUSY_MASK = 0x01 # Location (by mask) of busy bit located in the status register
STATUS_REG_VAL = 0x00 # Value of status register busy bit , when device is not busy.
# The device is considered not busy when:
# [status register value] & STATUS_BUSY_MASK = STATUS_REG_VAL
# Define the protected sectors.
# -----------------------------
#PROTECTED_SECTORS = 0-4 # Protected sectors (0 to 4)
[END CONFIG]

[cyberpark]

I think winflash doesn't accept different platform.
I advise you need dos base to flash bios, than windows based winflash.

try the backup bios on dos, 1234s282 added.

phlash16.exe BIOS.WPH /BBL /S /X /C /MODE=3

It would be better to keep on backup current bios, but I don't think the backup bios can be flash.

And it is too risk to update bios with other unknown bios, it might be slotech or samsung netbook, etc...

If you are willing to go head against worst case, like as blank screen, I would like to stick these.
board id: bearg31a
vga: Intel GMA 3150

it looks like as samsung NB30 or N148... but don't know exact what is the difference.

well, if in my shoes, I will try the backup bios, fails? then software crack, activator, or stick on xp. because it isn't mine, and too risky.

[LatinMcG75]

its definitely soltech pt21 no doubt.
i think i have to flash EC first but it wont go cause i think the people that rebranded changed bios and EC identifiers.

i tried it all phlash16 phlash167.

boardid should be Soltech PT21 according to winphlash advanced section with the original bios loaded to flash
http://tinyurl.com/fakevaioPT21

[LatinMcG75]

more info on the flupdate or nuvoton ec flash
www.gaodi.net/forum.php?mod=viewthread&tid=135884&archiver=1

[cyberpark]

The update files have bios and embedded keyboard controller update.

nuvoton ec flash is for embedded keyboard controller update.
and phoneix is for mainboard bios update.

you can get Nuvoton FlashUpdate_UserGuide.pdf from the below.

http://global-download.acer.com/GDFiles/...6534210852&Step1=Notebook&Step2=Aspire&Step3=Aspire%205740&OS=722&LC=en&BC=Acer&SC=PA_6

you can skip embedded keyboard controller update, but don't know what it makes difference exactly.

2. RELEASE NOTES
-----------------
# AUTHOR: Joe Chen
# REVIEWERS:
# SCOPE: PT21 BIOS, Flash Tool
# FILE: DEVEL35P.ROM - BIOS image used by Flash ROM programmer only.
# FLASHABL.ROM - BIOS image used by PT21 flash tool only.
# WPC.ROM - EC image used by both Flash ROM programmer and PT21 flash tool.
# PT21 flash tool.zip - BIOS and EC ISP flash tools.
# DATE: 2010-03-11
#
# WARNING: DO NOT flash BIOS by Flash ROM programmer with FLASHABL.ROM, and DO NOT flash
# BIOS by PT21 flash tool with DEVEL35P.ROM. Wrong usage of these ROMs may cause
# the BIOS not work.

look at these files what you posted.

HP modded slic 2.1 for PT21
http://lzerp.com/bbs/attachment.php?aid=8825&k=57e45bd8c7223818ccedc4ed70393e5c&t=1298745228&sid=Ook6t0

Original PT21
http://www.soltech.com.cn/uploads/PT21_B1.0_E1.0.zip

The HP modded one has change name from FLASHABL.ROM to PT21HP.ROM and /Force option on PT21HP.bat, but there isn't WPC.ROM as original PT21 file.

If you no doubt it, run phlash16.exe BIOS.WPH /Force /BBL /S /X /C /MODE=3 on pure dos.
and skip the embedded keyboard update, nuvoton ec flash.

[LatinMcG75]

i have tried to flash with phlash16 v 1.7.0.7 it says Part id not found in table of supported parts.
all methods fail so far.
i think i have to use recovery method to force it.
the flupdate.exe i have isnt the same as nuvoton page. its older cause the switch -novr -pfu dont work with it.

according to winphlash i have 2 chips.. W25X80 (001200EF) and MX25l800 (001300C2)